3.7
Owner's of the Rowenta Iron DX9000 gave it a score of 3.7 out of 5. Here's how the scores stacked up:
3 Way Auto-Off (depending on model)
If your iron is equipped with auto-off and
the iron is not moved while it is plugged in,
an internal safety switch will turn it off. It
will turn off in 8 minutes if left vertically or
in 30 seconds if left on its soleplate or tip-
ped over.
Models equipped with auto-off system –
A red light will flash when the auto-off
feature has engaged. To deactivate feature,
move the iron or shake it gently. Wait until
iron is fully reheated before use.
Models equipped with LED Display System –
The LED Light Display System will flash all
3 colors alternately when the feature has
activated. To deactivate feature, move the
iron or shake it gently. Wait until iron is fully
reheated before use.
Auto-Off is not an on/off switch. Always unplug when not
in use.
Filling
• Ensure the iron is unplugged.
• Slide the variable steam lever to the left (min).
• Rest iron on heel and tilt it forward approxi-
matley 1 inch. Open the water filler inlet by
pressing the push-button. You will hear it
click open.
• Fill with water to the max mark on the water
tank. We recommend using a water pitcher
rather than filling under the tap. Iron holds
approximately 13 oz of water.
• Close the filling inlet by pressing the push-
button. Be sure to close before returning to
the horizontal position.
If you need to add water during ironing, unplug the iron and
follow the steps above. Ensure iron heats back to temperature:
– indicator light turns green on models with LED Light
display system
– light will go out on irons not equipped with the LED Light
display system.
Water Recommendations
Tap water
Rowenta irons are designed to be used with REGULAR TAP
WATER (up to 12 grains of hardness). If your water is harder
than this, Rowenta recommends mixing half tap water with
half distilled water which reduces the hardness; or just use
bottled spring water. Never use 100 % distilled water as
this can cause the iron to spit and leak.
Before use
• Remove soleplate cover before using iron.
Remove all packaging from the iron.
• Please read all of the instructions for use
and the Important Safeguards carefully.
• It is normal for a small amount of smoke
and a light odor to be produced the first
time it is used. This will quickly disappear.
Helpful Hints
• When ironing start with fabrics that require a low tempera-
ture setting (•) and finish with those which need the highest
temperature (•••).
• Mixed fiber fabrics should be ironed on the temperature for
the most delicate fabric. For example a shirt that is 60%
cotton and 40% polyester should be ironed at the (•) setting
for synthetics.
• If spray starch is used, spray it onto the reverse side of the
garment. Allow starch to penetrate before ironing by set-
ting garment aside for 30 seconds.
• For best results, use a mesh type ironing board to allow
excess steam to escape.
• For delicate fabrics, we recommend carrying out a test on
an unobtrusive area of the garment such as an inner seam.
• Adhere to manufacturer recommendations on garment
label.
Light Display System (depending on model)
Some models of the Perfect iron are equipped
with an LED Light Display System. This
system will inform you when the iron is
heating and when it has reached ideal
temperature. It will also notify you when
the auto-off feature has engaged.
Steam Ironing
WARNING: Never Iron or steam clothes while they are
being worn. When iron is placed on heel, it will burst one
more time before Intra Steam stops. Use caution and do
not direct soleplate at people, animals, etc.
Before ironing for the first time fill iron and allow to heat.
The iron should be allowed to emit steam for at least
1 minute to remove any impurities. Meanwhile press from
time to time the burst of steam button. This should also
be done if iron isn’t used regularly.
Intra Steam (depending on model) –
The Intra Steam system generates higher
steam pressure to enable the steam to
penetrate faster and deeper into the fabric.
The steam is emitted in frequent bursts rather
than continuously. The pressure generated
will cause a burst noise. This is normal. As
this steam is so powerful and concentrated,
you may opt not to keep the steam on the maximum setting.
If you choose to keep it on maximum, more frequent filling
will be necessary. To set the intra steam level, move the
steam lever to the desired setting.
With the intra steam system, steam can be produced from
•• temperature setting the colored position on dial to the •••
setting. Maximum steam setting should only be used when
the iron is set to the highest temperature setting (•••). Steam
will be produced when the iron is used horizontally.
Burst of Steam – This feature is ideal for
removing stubborn wrinkles or pressing in
sharp creases.
When the temperature control is set to a
steam setting (•• or •••) the burst of steam
can be used. Press the button to generate a
burst of steam. Leave an interval of at least
four seconds between bursts.
Vertical Steam – This feature is ideal for
hanging clothes, drapes, curtains, etc.
When the temperature control is set to a
steam setting vertical steam can be used. To
use feature, hold iron vertically with the tip
tilted forward slightly. Press the burst of
steam button repeatedly while moving iron
from bottom of garment to top. If vertical
steam output starts to decrease tilt iron for-
ward to a horizontal position and then back
to vertical to continue.
Spray Setting
This feature is ideal for stubborn wrinkles or
set in creases. Ensure there is water in the
tank then press the spray button. Do not
spray silk.
IMPORTANT SAFETY INSTRUCTIONS
When using this appliance, basic safety precautions should
always be followed including the following:
Read all instructions before using this product.
• Use appliance only for its intended use.
• To protect against a risk of electric shock, do not immerse
the appliance in water or other liquids.
• The appliance should always be turned off before plugging
or unplugging from outlet. Never yank the cord to disconnect
from outlet, instead grasp plug and pull to disconnect.
• Always disconnect appliance from electrical outlet when
filling with water or emptying when not in use.
• Do not allow cord to touch hot surfaces. Let iron cool
completely before putting away. Loop cord loosely around
iron when storing.
• Do not operate appliance with a damaged cord or if
appliance has been dropped or damaged.
• To avoid the risk of electric shock, do not disassemble the
appliance. Ship it to the nearest authorized Rowenta
approved service center for examination and repair.
Incorrect reassembly can cause a risk of electric shock
when the appliance is used.
• Not intended for use by children. Close supervision is
necessary for any appliance being used near children.
Unsupervised use can result in fire or personal injury.
Do not leave appliance unattended while plugged in,
on an ironing board, or while it is still hot.
• Burns can occur from touching hot metal parts, hot water or
steam. Use caution when you turn a steam iron upside
down. There may be hot water in the reservoir.
• Do not direct steam at people, animals or iron clothes while
they are being worn.
• The use of accessory attachments is not recommended by
Rowenta and may result in fire, electric shock or personal
injury.
SPECIAL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
• This is a 1600 watt appliance. To avoid a circuit overload, do
not operate a high wattage appliance on the same circuit.
• If an extension cord is absolutely necessary, the marked
electrical rating should be at least as great as the electrical
rating of the appliance. Cords rated for less amperage may
overheat. Care should be taken to arrange the cord so that it
cannot be pulled or tripped over unintentionally.
• Your Rowenta appliance is intended for household use only.
Softened water
There are many types of household water softeners and the
water from many of them is perfectly acceptable for use in
an iron. However, some types of softeners, particularly those
that use chemicals such as salt, can cause the appliance to
leak or spit during use. If you experience this type of problem,
we recommend that you try using bottled spring water or
untreated tap water. Never use 100 % distilled water.
Once you have changed water it will take several uses to
correct the problem. Rowenta recommends trying the
steam function for the first time on an old towel or cloth
that can be discarded to avoid damaging your clothes.
Iron and other impurities
If your water supply contains large amounts of iron or
organic matter, these minerals can collect inside the
appliance and eventually appear as brown stains. If you
experience these problems Rowenta recommends using
bottled spring water. Never use 100 % pure distilled water.
Always remember:
Battery water and water containing additives (such as
starch, perfume or fabric conditioner condensed water
from driers) may not be used. Such additives can affect the
properties of the steam and, at high temperatures, can
form deposits in the steam chamber, which will mark the
laundry when they are emitted through the steam vents.
Descaling liquids/agents should not be used.
Selecting the Temperature
Models equipped with a temperature dial –
Set the temperature control dial according
to the fabric you are ironing. Check the gar-
ment’s label for appropriate setting. We
recommend using the chart below as a
guide. Light will be on as iron is heating.
When light goes out iron is ready to use.
Models equipped with Electronic Temperature Control
(Thermo Control)
The iron has an electronic sensor that monitors the tempe-
rature of the soleplate and ensures it is accurate. The ther-
mostat light will be yellow as the iron is heating. Once the
correct temperature is reached the light will turn green. We
recommend using the chart below as a guide to set the iron:
LED display
You can start ironing
now. The soleplate is at
the optimum tempera-
ture for your material.
Wait for the iron to cool
down to the selected
temperature and the
LED display to switch
to GREEN.
Allow iron to finish
heating.
What to do
The soleplate is
at the right tem-
perature for the
selected material.
The soleplate is
still too hot for
the selected
material.
The soleplate is
not hot enough.
This means:Colour
YELLOW
GREEN
RED
Ironing label Fabric
Synthetics e.g.
polyester, silk, viscose
Wool
Cotton, linen
Temperature control
DX9000 - USA 13.05.2003 15:04 Uhr Seite 2
Find Your Products By Category
Please Login
