0

Out of 0 Ratings

Owner's of the KitchenAid Mixer KSM8990WH gave it a score of 0 out of 5. Here's how the scores stacked up:
  • Reliability

    0 out of 5
  • Durability

    0 out of 5
  • Maintenance

    0 out of 5
  • Performance

    0 out of 5
  • Ease of Use

    0 out of 5
of 70
 
7
Assembling Your Bowl-Lift Stand Mixer
Pre-Use Cleaning
Before using your Stand Mixer for the first
time, wash the mixing bowl and accessories
(see “Care and Cleaning” on page 14).
Attaching Mixing Bowl
1. Be sure speed control is OFF and mixer
is unplugged.
2. Place bowl lift handle in down position.
3. Fit bowl supports over locating pins.
4. Press down on back of bowl until
bowl pin snaps into spring latch.
5. Raise bowl before mixing.
6. Plug mixer in proper electrical outlet
(see page 4).
Removing Mixing Bowl
1. Be sure speed control is OFF and mixer
is unplugged.
2. Place bowl lift handle in down
position.
3. Remove flat beater, Wire Whip*, or
Dough Hook*.
4. Grasp bowl handle and lift straight up
and off locating pins.
Raising Mixing Bowl
1. Rotate handle to straight-up position.
2. Bowl must always be in raised, locked
position when mixing.
Lowering Mixing Bowl
1. Rotate handle back and down.
Attaching Flat Beater, Wire Whip*, or
Dough Hook*
1. Turn speed control to OFF and unplug.
2. Slip flat beater on beater shaft and
press upward as far as possible.
3. Turn beater to
right, hooking
beater over the
pin on shaft.
4. Plug mixer in
proper electrical outlet (See page 4).
Removing Flat Beater, Wire Whip*, or
Dough Hook*
1. Turn speed control to OFF and unplug.
2. Press beater upward as far as possible
and turn left.
3. Pull beater from beater shaft.
4. Plug mixer in proper electrical outlet
(See page 4).
Household Stand Mixer
Speed Control
Plug mixer in proper electrical outlet
(See page 4). Speed control lever should
always to be set on lowest speed for
starting, then gradually moved to
desired higher speed to avoid splashing
ingredients out of bowl. See page 10 for
Speed Control Guide.
Overload Reset Button
Model KSMC50 Only
If the mixer is overloaded,
the Overload Reset Button
will pop out and the mixer
will shut off. Turn the Speed
Control Lever to OFF. Wait a few minutes,
then push in the Reset Button. Turn the
Speed Control Lever to the desired speed
and continue mixing.
C
A
U
T
I
O
N
:
U
n
p
l
u
g
b
e
f
o
r
e
i
n
s
e
r
t
i
n
g
o
f
r
e
m
o
v
i
n
g
p
a
r
t
s
Heavy Duty
PIN
Solid State Speed Contr
ol
Of
f Stir 2 4 6 8 10
Comm
er
cial
O
v
e
rl
o
a
d
Re
se
t
* Sold separately for model K4SS.
Injury Hazard
Unplug mixer before touching
beaters.
Failure to do so can result in
broken bones, cuts or bruises.
WARNING
M
o
d
e
l
K
5
S
S
M
a
x
.
W
a
tts
3
2
5
V
o
lts
1
1
5
H
z
6
0
HOUSEHOLD
USE ON
LY
M
a
d
e in
U
.S.A
.
Heavy
Dut
y
C
A
U
T
I
O
N
:
U
n
p
l
u
g
b
e
f
o
r
e
i
n
s
e
r
t
i
n
g
of
re
mo
ving
pa
rt
s
RAISE